High Color-Purity and Efficient Pure-Blue Perovskite Light-Emitting Diodes Based on Strongly Confined Monodispersed Quantum Dots.

Here, we develop an in situ photoluminescence (PL) system to monitor the nucleation and growth of perovskite nanocrystals and control the monomer supply rate to achieve strongly confined and monodispersed quantum dots (QDs) with average size of 3.4 nm. Pure-blue (460 nm wavelength) CsPbBr3 QDs with near unity PL quantum yield and narrow size distribution (small size dispersion of 9.6%) were thus produced. Light-emitting diodes (LEDs) based on these QDs were prepared by using an all-solution processing route, which showed narrow electroluminescence with full width at half-maximum of 20 nm and a high color purity of 97.3%. The device also had a high external quantum efficiency of 10.1%, maximum luminance of 11 610 cd m-2, and continuous operation lifetime of 21 h at the initial luminance of 102 cd m-2, corresponding to the state-of-art for pure-blue perovskite LEDs.

A Low-Temperature Synthetic Route Toward a High-Entropy 2D Hexernary Transition Metal Dichalcogenide for Hydrogen Evolution Electrocatalysis.

High-entropy (HE) metal chalcogenides are a class of materials that have great potential in applications such as thermoelectrics and electrocatalysis. Layered 2D transition-metal dichalcogenides (TMDCs) are a sub-class of high entropy metal chalcogenides that have received little attention to date as their preparation currently involves complicated, energy-intensive, or hazardous synthetic steps. To address this, a low-temperature (500 °C) and rapid (1 h) single source precursor approach is successfully adopted to synthesize the hexernary high-entropy metal disulfide (MoWReMnCr)S2 . (MoWReMnCr)S2 powders are characterized by powder X-ray diffraction (pXRD) and Raman spectroscopy, which confirmed that the material is comprised predominantly of a hexagonal phase. The surface oxidation states and elemental compositions are studied by X-ray photoelectron spectroscopy (XPS) whilst the bulk morphology and elemental stoichiometry with spatial distribution is determined by scanning electron microscopy (SEM) with elemental mapping information acquired from energy-dispersive X-ray (EDX) spectroscopy. The bulk, layered material is subsequently exfoliated to ultra-thin, several-layer 2D nanosheets by liquid-phase exfoliation (LPE). The resulting few-layer HE (MoWReMnCr)S2 nanosheets are found to contain a homogeneous elemental distribution of metals at the nanoscale by high angle annular dark field-scanning transmission electron microscopy (HAADF-STEM) with EDX mapping. Finally, (MoWReMnCr)S2 is demonstrated as a hydrogen evolution electrocatalyst and compared to 2H-MoS2 synthesized using the molecular precursor approach. (MoWReMnCr)S2 with 20% w/w of high-conductivity carbon black displays a low overpotential of 229 mV in 0.5 M  H2 SO4 to reach a current density of 10 mA cm-2 , which is much lower than the overpotential of 362 mV for MoS2 . From density functional theory calculations, it is hypothesised that the enhanced catalytic activity is due to activation of the basal plane upon incorporation of other elements into the 2H-MoS2 structure, in particular, the first row TMs Cr and Mn.

Synthesis and characterisation of Ga- and In-doped CdS by solventless thermolysis of single source precursors.

We report a facile and low temperature synthesis of Ga- and In-doped CdS nanoparticles from molecular precursors. Diethyldithiocarbamate complexes of Cd(II), Ga(III), and In(III), were synthesised and decomposed in tandem through solventless thermolysis, producing Ga- or In-doped CdS. The resultant MxCd1-xS1+0.5x (where M = Ga/In at x values of 0, 0.02, 0.04, 0.06, 0.08 and 0.1) particulate powder was analysed by powder X-ray diffraction, which showed that both Ga (through all doping levels) and In (at doping levels <8 mol%) were successfully incorporated into the hexagonal CdS lattice without any impurities. Raman spectroscopy also showed no significant change from CdS. Scanning electron microscopy and energy dispersive X-ray spectroscopy were used to investigate the morphology and elemental dispersion through the doped CdS materials, showing homogenous incorporation of dopant. The optical and luminescent properties of the doped MxCd1-xS1+0.5x materials were examined by UV-Vis absorption and photoluminescence spectroscopies respectively. All materials were found to exhibit excitonic emission, corresponding to band gap energies between 2.7 and 2.9 eV and surface defect induced emission which is more prominent for Ga than for In doping. Additionally, moderate doping slows down charge carrier recombination by increasing the lifetimes of excitonic and surface state emissions, but particularly for the latter process.

Quantum Confined High-Entropy Lanthanide Oxysulfide Colloidal Nanocrystals.

We have synthesized the first reported example of quantum confined high-entropy (HE) nanoparticles, using the lanthanide oxysulfide, Ln2SO2, system as the host phase for an equimolar mixture of Pr, Nd, Gd, Dy, and Er. A uniform HE phase was achieved via the simultaneous thermolysis of a mixture of lanthanide dithiocarbamate precursors in solution. This was confirmed by powder X-ray diffraction and high-resolution scanning transmission electron microscopy, with energy dispersive X-ray spectroscopic mapping confirming the uniform distribution of the lanthanides throughout the particles. The nanoparticle dispersion displayed a significant blue shift in the absorption and photoluminescence spectra relative to our previously reported bulk sample with the same composition, with an absorption edge at 330 nm and a λmax at 410 nm compared to the absorption edge at 500 nm and a λmax at 450 nm in the bulk, which is indicative of quantum confinement. We support this postulate with experimental and theoretical analysis of the bandgap energy as a function of strain and surface effects (ligand binding) as well as calculation of the exciton Bohr radiii of the end member compounds.

Synthesis of High Entropy Lanthanide Oxysulfides via the Thermolysis of a Molecular Precursor Cocktail.

High entropy (HE) materials have received significant attention in recent years, due to their intrinsically high levels of configurational entropy. While there has been significant work exploring HE alloys and oxides, new families of HE materials are still being revealed. In this work we present the synthesis of a novel family of HE materials based on lanthanide oxysulfides. Here, we implement lanthanide dithiocarbamates as versatile precursors that can be mixed at the molecular scale prior to thermolysis in order to produce the high entropy oxysulfide. The target of our synthesis is the HE Ln2SO2 phase, where Ln = Pr, Nd, Gd, Dy, Er and where Ln = Pr, Nd, Gd, Dy for 5 and 4 lanthanide samples, respectively. We confirmed the structure of samples produced by powder X-ray diffraction, electron microscopy, and high-resolution energy dispersive X-ray spectroscopy. Optical spectroscopy shows a broad emission feature centered around 450 nm as well as a peak in absorption at around 280 nm. From this data we calculate the band gap and Urbach energies of the materials produced.

Synthesis, X-ray Single-Crystal Structural Characterization, and Thermal Analysis of Bis(O-alkylxanthato)Cd(II) and Bis(O-alkylxanthato)Zn(II) Complexes Used as Precursors for Cadmium and Zinc Sulfide Thin Films.

This work investigates tuning of the molecular structure of a series of O-alkylxanthato zinc and cadmium precursor complexes to enhance production of ZnS and CdS materials. The structures of several bis(O-alkylxanthato) cadmium(II) complexes (8-13) and bis(O-alkyl xanthato)zinc(II) complexes (18 and 19) are reported based on single crystal X-ray diffraction data. CdS and ZnS films were produced by the spin-coating of these metal complexes followed by their thermal decomposition to the corresponding metal sulfides. Thin films of CdS were deposited by spin-coating the bis(O-alkylxanthato) cadmium(II) precursors (7-13) on glass substrates, followed by annealing at 300 °C for 60 min. Thin films of ZnS were deposited by spin-coating bis(O-alkylxanthato) zinc(II) (14-20), followed by annealing at 200 °C for 60 min. The molecular complexes and solid state materials are characterized using a range of techniques including single-crystal X-ray diffraction, pXRD, EDS and XPS, DSC and TGA, UV-vis and PL spectroscopies, and electron microscopy. These techniques provided information on the influence of alkyl chain length on the thermal conditions required to fabricate metal sulfide films as well as film properties such as film quality, and morphology. For example, the obtained crystallite size of metal sulfide films formed is correlated to the hydrocarbon chain length of xanthate ligands in the precursor. The behavior of the complexes under thermal stress was therefore studied in detail. DTA and TGA profiles explain the relationship between hydrocarbon chain length, decomposition temperatures, and the energies required for decomposition. A higher decomposition temperature for complexes with longer hydrocarbon chains is observed compared to complexes with shorter hydrocarbon chains. Band-gap energies calculated from the optical absorption spectra alongside steady state and time-resolved photoluminescence studies are reported for CdS films.

Engineering Halide Perovskite Crystals through Precursor Chemistry.

The composition, crystallinity, morphology, and trap-state density of halide perovskite thin films critically depend on the nature of the precursor solution. A fundamental understanding of the liquid-to-solid transformation mechanism is thus essential to the fabrication of high-quality thin films of halide perovskite crystals for applications such as high-performance photovoltaics and is the topic of this Review. The roles of additives on the evolution of coordination complex species in the precursor solutions and the resulting effect on perovskite crystallization are presented. The influence of colloid characteristics, DMF/DMSO-free solutions and the degradation of precursor solutions on the formation of perovskite crystals are also discussed. Finally, the general formation mechanism of perovskite thin films from precursor solutions is summarized and some questions for further research are provided.

Stable and Strong Emission CsPbBr3 Quantum Dots by Surface Engineering for High-Performance Optoelectronic Films.

We demonstrated complete surface passivation of CsPbBr3 quantum dots (QDs) by treatment with di-dodecyldimethylammonium bromide (DDAB) and sodium thiocyanate (NaSCN), resulting in dispersions with photostable photoluminescence of near-unity quantum yield (∼100%) as well as high carrier mobility of QDs' film. Br- from DDAB and SCN- from NaSCN passivated the bromine vacancies of the QDs to reduce the surface defect density and increase the stability. The QDs-passivated maintained the original photoluminescence intensity under ultraviolet irradiation from a 150 W xenon lamp for 1 h, whereas the PL intensity of QDs-control dropped quickly to 20% of its initial value. The shorter DDA+ ligands also improved carrier transport in the QDs-passivated film, which was verified by conductivity and space charge limited current measurements. When used as the photoemitting species in a solution-processed light-emitting diode structure, the surface treatment increased the maximum luminance from 550 to 1200 cd·m-2 and reduced the turn-on voltage from 3.1 to 2.8 V.

Enhanced-performance of self-powered flexible quantum dot photodetectors by a double hole transport layer structure.

The usefulness of self-powered quantum dot (QD) photodetectors is increased if they are fabricated on flexible substrates. However, the performance of such photodetectors is typically significantly worse than similar devices fabricated on glass substrates due to poor charge transport performance. Here, a novel flexible self-powered CdSexTe1-x QD photodetector with a double hole transport layer of PEDOT:PSS/P-TPD has been fabricated, which achieves a performance comparable to that of rigid devices. The energy level of the P-TPD layer matches well with that of the PEDOT:PSS and QD layers, which significantly enhances photodetection capability across a spectral region that spans the ultraviolet, visible and near infrared (UV-NIR). A low dark current density (1.03 × 10-6 mA cm-2) and a large specific detectivity of approximately 2.6 × 1012 Jones at a wavelength of 450 nm are demonstrated, significantly outperforming previously reported flexible QD-based detectors. This improvement in performance is attributed to both increased hole transport efficiency and the inhibition of electron transport from the QDs into the PEDOT:PSS layer. The photodetector also exhibits good sensitivity under weak illumination, producing a photocurrent of 196 × 10-6 mA cm-2 under an irradiance of 5 µW cm-2. Moreover, no significant performance degradation is observed after 150 bending cycles to an angle of 60 degrees.

Confinement Effects and Charge Dynamics in Zn3N2 Colloidal Quantum Dots: Implications for QD-LED Displays.

Zinc nitride (Zn3N2) colloidal quantum dots are composed of nontoxic, low-cost, and earth-abundant elements. The effects of quantum confinement on the optical properties and charge dynamics of these dots are studied using steady-state optical characterization and ultrafast fluence-dependent transient absorption. The absorption and emission energies are observed to be size-tunable, with the optical band gap increasing from 1.5 to 3.2 eV as the dot diameter decreased from 8.9 to 2.7 nm. Size-dependent absorption cross sections (σ = 1.22 ± 0.02 × 10-15 to 2.04 ± 0.03 × 10-15 cm2), single exciton lifetimes (0.36 ± 0.02 to 0.65 ± 0.03 ns), as well as Auger recombination lifetimes of biexcitons (3.2 ± 0.4 to 5.0 ± 0.1 ps) and trions (20.8 ± 1.8 to 46.3 ± 1.3 ps) are also measured. The degeneracy of the conduction band minimum (g = 2) is determined from the analysis of the transient absorption spectra at different excitation fluences. The performance of Zn3N2 colloidal quantum dots thus broadly matches that of established visible light emitting quantum dots based on toxic or rare elements, making them a viable alternative for QD-LED displays.

Erratum: Ultrafast Charge Dynamics in Trap-Free and Surface-Trapping Colloidal Quantum Dots.

[This corrects the article DOI: 10.1002/advs.201500088.].

Effect of Chloride Passivation on Recombination Dynamics in CdTe Colloidal Quantum Dots.

Colloidal quantum dots (CQDs) can be used in conjunction with organic charge-transporting layers to produce light-emitting diodes, solar cells and other devices. The efficacy of CQDs in these applications is reduced by the non-radiative recombination associated with surface traps. Here we investigate the effect on the recombination dynamics in CdTe CQDs of the passivation of these surface traps by chloride ions. Radiative recombination dominates in these passivated CQDs, with the radiative lifetime scaling linearly with CQD volume over τr =20-55 ns. Before chloride passivation or after exposure to air, two non-radiative components are also observed in the recombination transients, with sample-dependent lifetimes typically of less than 1 ns and a few ns. The non-radiative dynamics can be explained by Auger-mediated trapping of holes and the lifetimes of this process calculated by an atomistic model are in agreement with experimental values if assuming surface oxidation of the CQDs.

Near-unity quantum yields from chloride treated CdTe colloidal quantum dots.

Colloidal quantum dots (CQDs) are promising materials for novel light sources and solar energy conversion. However, trap states associated with the CQD surface can produce non-radiative charge recombination that significantly reduces device performance. Here a facile post-synthetic treatment of CdTe CQDs is demonstrated that uses chloride ions to achieve near-complete suppression of surface trapping, resulting in an increase of photoluminescence (PL) quantum yield (QY) from ca. 5% to up to 97.2 ± 2.5%. The effect of the treatment is characterised by absorption and PL spectroscopy, PL decay, scanning transmission electron microscopy, X-ray diffraction and X-ray photoelectron spectroscopy. This process also dramatically improves the air-stability of the CQDs: before treatment the PL is largely quenched after 1 hour of air-exposure, whilst the treated samples showed a PL QY of nearly 50% after more than 12 hours.

Ultrafast Charge Dynamics in Trap-Free and Surface-Trapping Colloidal Quantum Dots.

Ultrafast transient absorption spectroscopy is used to study subnanosecond charge dynamics in CdTe colloidal quantum dots. After treatment with chloride ions, these can become free of surface traps that produce nonradiative recombination. A comparison between these dots and the same dots before treatment enables new insights into the effect of surface trapping on ultrafast charge dynamics. The surface traps typically increase the rate of electron cooling by 70% and introduce a recombination pathway that depopulates the conduction band minimum of single excitons on a subnanosecond timescale, regardless of whether the sample is stirred or flowed. It is also shown that surface trapping significantly reduces the peak bleach obtained for a particular pump fluence, which has important implications for the interpretation of transient absorption data, including the estimation of absorption cross-sections and multiple exciton generation yields.

Size dependence of ultrafast charge dynamics in monodisperse Au nanoparticles supported on TiO2 colloidal spheres.

Sub-nanosecond charge dynamics in monodisperse Au nanoparticles (NPs) supported on TiO2 colloidal spheres are studied as a function of NP diameter using ultrafast transient absorption spectroscopy. The decay of the transmittance changes observed in the region of the plasmon resonance of the Au NPs following photoexcitation of the TiO2 spheres are well-described by a bi-exponential function consisting of a fast component of 2 ps duration associated with electron-phonon scattering, followed by a slow and relatively weak component associated with phonon-phonon scattering. The decay constant characterising the latter component was found to be dependent on the size of the Au NPs, rising from 49 ± 3 to 128 ± 6 ps as the diameter of the Au NPs increased from 12.2 ± 2.2 nm to 24.5 ± 2.8 nm, respectively.

Multiple exciton generation and ultrafast exciton dynamics in HgTe colloidal quantum dots.

The investigation of sub-nanosecond exciton dynamics in HgTe colloidal quantum dots using ultrafast transient absorption spectroscopy is reported. The transmittance change spectrum acquired immediately after pumping is dominated by a bleach blue-shifted by ~200-300 nm from the photoluminescent emission band. Comparison with a tight-binding model of the electronic structure allows this feature to be attributed to the filling of band edge states. The form of the pump-induced transmittance transients is dependent on the excitation rate and the rate of sample stirring. For moderate pumping of stirred samples, the transmittance transients are well-described by a mono-exponential decay associated with biexciton recombination, with a lifetime of 49 ± 2 ps. For samples that are strongly-pumped or unstirred, the decay becomes bi-exponential in form, indicating that trap-related recombination has become significant. We also present a new analysis that enables fractional transmittance changes to be related to band edge occupation for samples with arbitrary optical density at the pump wavelength. This allows us to identify the occurrence of multiple exciton generation, which results in a quantum yield of 1.36 ± 0.04 for a photon energy equivalent to 3.1 times the band gap, in good agreement with the results of the model.

Multiple Exciton Generation in Colloidal Nanocrystals.

In a conventional solar cell, the energy of an absorbed photon in excess of the band gap is rapidly lost as heat, and this is one of the main reasons that the theoretical efficiency is limited to ~33%. However, an alternative process, multiple exciton generation (MEG), can occur in colloidal quantum dots. Here, some or all of the excess energy is instead used to promote one or more additional electrons to the conduction band, potentially increasing the photocurrent of a solar cell and thereby its output efficiency. This review will describe the development of this field over the decade since the first experimental demonstration of multiple exciton generation, including the controversies over experimental artefacts, comparison with similar effects in bulk materials, and the underlying mechanisms. We will also describe the current state-of-the-art and outline promising directions for further development.

Ultrafast exciton dynamics in InAs/ZnSe nanocrystal quantum dots.

Colloidal nanocrystal quantum dots with a band gap in the near infra-red have potential application as the emitters for telecommunications or in vivo imaging, or as the photo-absorbing species in next generation solar cells or photodetectors. However, electro- and photoluminescence yields and the efficiency with which photo-generated charges can be extracted from quantum dots depend on the total rate of recombination, which can be dominated by surface-mediated processes. In this study, we use ultrafast transient absorption spectroscopy to characterise the recombination dynamics of photo-generated charges in InAs/ZnSe nanocrystal quantum dots. We find that recombination is dominated by rapid, sub-nanosecond transfer of conduction band electrons to surface states. For the size of dots studied, we also find no evidence of significant multiple exciton generation for photon energies up to 3.2 times the band gap, in agreement with our theoretical modelling.

Enhanced photosynthetic output via dichroic beam-sharing.

Microbial solar biofuels offer great promise for future sustainable food, fuels and chemicals but are limited by low productivities and a requirement for large land areas to harvest sunlight. A 71 % increase in combined photosynthetic activity was achieved by illuminating both Rhodobacter sphaeroides and Arthrospira (Spirulina) platensis from a single beam of simulated sunlight, divided using a dichroic mirror. Therefore, this technique is termed 'dichroic beam-sharing', in which the complementary action spectra of two different useful micro-organisms, belonging to green and purple groups, is exploited and allows a single beam of sunlight to be shared efficiently between separate photobioreactors. Because the action spectra of these two organisms are typical of large groups, this novel method could increase the productivity of photosynthetic micro-organisms in the production of diverse commodities.

Evaluation of a digital flocculation reader for the rapid plasma reagin test for the serological diagnosis of syphilis.

We described the ASiManager-AT digital flocculation reader to demonstrate concordance between visual and digital readings of the rapid plasma reagin test for detection of antibodies in the serum of patients with syphilis. A qualitative and quantitative rapid plasma reagin was performed on each serum samples giving a concordance of 98.6% and 99.7%, respectively, for reactives and 100% for nonreactives.